Brick Paver Installation & Edging



Staging of product

Many paver tasks will vary depending upon access, website conditions, job size and naturally, the weather. These scenarios can have a general impact on your job from a timing stand point. Careful factor to consider should be required to determine the time to begin the paver installation. Constantly try to prevent any traffic or minimize on the prepared locations.

The foreman or job manager ought to constantly have the materials (sand/ pavers) dispersed around the project website for effective and simple setups. Paver pallets/bundles need to be put in a way not to interfere with the paver installation. The appropriate pallet/bundle placement can make the real job installation much easier and quicker by decreasing the general labor of managing the material.

Brick paver patterns

Pavers can be positioned in many different patterns depending on their shape. Each paver shape will usually have several various hatch patterns that are supplied by the manufacturer.

Professionals require to take into factor to consider the traffic weight loads on their paver projects. In many applications around the world, it has actually been shown that pavers laid in a herringbone pattern have performed sufficiently.

Pavers that are 60 mm (2 - 3/8 in) density are suitable for pedestrian applications. Pavers that are going to be used in industrial or commercial applications ought to be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a variety of conditions that determine the beginning point of a paver job.

When starting to set up pavers it is best to snap a true straight chalk line on the surface of the bed linen sand or pull a real straight string line above the surface of the bed linen sand at the completed elevation of the pavers This will assist as a guide for preserving straight joint lines and will also permit the installer to make adjustments in the positioning of the pavers.

Buildings and concrete suppressing are generally not straight and must not be used for developing straight joint lines. The use of string lines is vital to determine the true straightness of the edge too. As the paver installation advances, the string lines will help decrease the need for little trim pieces.

Joint width between pavers must be in between 1/16 and 3/16 in (2 and 5 mm ). There are some pavers with spacer bars on their sides. These will maintain a minimum joint width and permit the bedding and jointing sand to get in between each paver. Pavers with spacer bars are normally not laid in snug against each other considering that a string line will provide consistent joint spacing.

Installation of brick pavers.

Among the most widely used methods for the installation of pavers is hand installation of each paver. It is best to set up a single row of pavers along among the true straight lines that you have pulled or above the bed linen sand. This will offer you a real and straight line off which to work. Once this row is established, you can continue to work outside into the field with the remainder of the pavers. Always ensure to occasionally check your joint lines to make sure they are real and straight. If not, adjustments to the pavers can be made as you continue installing. Pavers needs to be installed hand tight. The best technique is to position a paver against another one and let it move down into the bed linen sand. Do not kick or tap the pavers into place as this can throw your lines out of true straightness.

When installing pavers on a steep grade, they ought to be set up at the base of the grade going uphill. This will avoid the pavers from sneaking as they are being laid.

On large industrial and commercial applications, hand laying pavers would not be cost effective due to the labor strength. The very best way for installing pavers on big tasks is to install them mechanically. The use of a mechanical laying machine can install around 6000 - 7000 sq ft a day. There are a couple products a contractor ought to consider prior to setting up pavers mechanically:

1.) Mechanical installers are only capable of installing pavers in specific patterns.

2.) The specialist needs to make sure that the manufacturer is capable of manufacturing and bundling pavers in the preferred pattern on the pallets for simple mechanical installation.

3.) Specialists may encounter a color blending circumstance coming off the packages of pavers Poor color mixing might lead to an irregular looking installation. Most manufacturers are consistent with color mixing on each package of pavers, however it is the specialist's duty to ensure proper mixing in the field.

Cutting treatments for brick pavers.

Contractors typically have two ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will offer a much cleaner and more accurate cut. Many brick saws will have a hose pipe attachment on them which will enable the operator to cut the pavers wet. When cutting pavers wet, it will help minimize dust and will prolong the diamond blades life. The operator of the brick saw need to constantly cut the pavers far from the surface area of the paver field when cutting damp, due to the fact that the pavers will produce a slurry that will stain the paver surface. Pavers that are cut ought to not fit tight, sufficient spacing should be available for jointing sand.

The brick saw operator ought to always wear the correct defense that is required for operating a saw, such as eye, ear, respiratory and hand protection ).

Edging types

Edge restraints play a significant function in the total success of an interlocking pavement installation Edging restraints remove lateral motion of the pavers and hold the pavers firmly together. Particularly at the outer perimeter of the paver application, without an edging restraint, your task is ensured to fail in time.

There are several various edging restraints from which specialists can select. Generally manufactured edge restraints are the most frequently utilized by professionals. Manufactured Tree Service Del Ray Beach edging restraints can range from, plastic edging, steel and aluminum, lumbers or precast concrete and stone. An edging type that is utilized primarily in commercial and commercial applications is poured-in-place concrete curbs. This edging restraint is typically set up by other professionals.

Edging installation.

This could result in the migration of the bed linen sand and eventual lateral motion of the pavers. If there is a possibility of losing bed linen sand between the pavers and the edge restraint, then geo textile material is recommended. When a space between the pavers and the edging goes beyond 3/8" (10mm), then the space needs to be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers have to be compacted. The whole area that is to be compressed should be swept tidy of any foreign objects and particles that can cause scuffing or scratching on the surface of the pavers.

It is essential to have a compactor that can apply between 3000lbs. And 5000 pounds. Of centrifugal compaction force. In addition, it is very important that the first compaction occurs before any jointing sand has been applied to the pavers. This can trigger a bridging problem and will not allow the joints to be entirely filled with jointing sand if jointing sand is applied to the pavers prior to compaction takes place. This can likewise avoid the pavers from being correctly set into the bed linen sand.

When compacting the pavers, it is advised that you make at least 2 passes in various directions throughout the pavers. This will allow the pavers to be correctly embeded in the bedding sand and will require the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is very vital to the final performance of the pavers. Failure to do correct compaction can result in deformations and pavement failure over time.


Paver pallets/bundles must be placed in a manner not to interfere with the paver installation. One of the most extensively used techniques for the installation of pavers is hand installation of each paver. The operator of the brick saw need to always cut the pavers away from the surface of the paver field when cutting damp, due to the fact that the pavers will produce a slurry that will stain the paver surface. Edging restraints eliminate lateral movement of the pavers and hold the pavers securely together. When a gap in between the pavers and the edging exceeds 3/8" (10mm), then the area needs to be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *